@article { author = {Yal Beiranvand, Sina and Nourani, Hossein and Kazemi Mehrjerdi, Hossein}, title = {Fabrication of Platelet-Rich Fibrin-Coated Polycaprolactone/Hydroxyapatite (PCL-HA/PRF) 3D Printed Scaffolds for Bone Tissue Engineering}, journal = {Iranian Journal of Veterinary Medicine}, volume = {16}, number = {4}, pages = {400-413}, year = {2022}, publisher = {University of Tehran}, issn = {2251-8894}, eissn = {2252-0554}, doi = {10.22059/ijvm.2022.335899.1005219}, abstract = { BACKGROUND: Tissue engineering is a potential technique for treating bone tissue abnormalities in the short and long terms. Aside from that, the use of 3D printing technology has considerable advantages in the production of bioengineering scaffolds for the treatment of patient-specific bone defects. OBJECTIVES: The aim of the study was to fabricate and characterize the 3D printed polycaprolactone/hydroxy-apatite (PCL-HA) scaffolds modified with Platelet-rich Fibrin (PRF). METHODS: The scaffolds were fabricated using 3D printing technology to provide a suitable environment for the bone regeneration. Scanning electron microscopy (SEM), Fourier transform infrared (FTIR), and compression tests were utilized to characterize the scaffold morphology, microstructure, and mechanical properties, respectively. The potentials for the cell adhesion, proliferation, biocompatibility, and differentiation were also investigated. RESULTS: The 3D PCL-HA scaffold with linked pores had a moderately rough surface as a result of hydroxyap-atite (HA) nanoparticles incorporation, which resulted in the increased mechanical properties. Increased bone cell proliferation on the PCL-HA/PRF scaffold surface was seen as a result of the enhanced hydrophilicity and porosity of the PCL-HA/PRF scaffold as compared to the PCL scaffold. The MTT assay results showed that the PCL-HA/PRF scaffold was much more cyto-compatible than the PCL and PCL-HA scaffolds, which was a major im-provement. CONCLUSIONS: The results showed that 3D printed PCL-HA scaffold supplemented with Platelet-rich Fibrin (PRF) may be an effective scaffold for the bone tissue regeneration.}, keywords = {3D printing scaffolds,Bone Tissue Engineering,Hydroxyapatite,osteogenic differentiation,Platelet-rich Fibrin}, title_fa = {ساخت داربست های چاپ سه بعدی شده پلی کاپرولاکتون/هیدروکسی آپاتیت پوشش داده شده با فیبرین غنی از پلاکت برای مهندسی بافت استخوان}, abstract_fa = {زمینه مطالعه: مهندسی بافت یک استراتژی امیدوارکننده برای ترمیم نقایص بافت استخوانی است. علاوه بر این، فناوری چاپ سه بعدی مزایای قابل توجهی در تولید داربست‌های مهندسی زیستی برای درمان نقایص استخوانی منحصربفرد برای هر بیمار ارائه می‌دهد.هدف: هدف از این مطالعه، سنتز و بررسی خواص داربست‌های چاپ سه بعدی پلی کاپرولاکتون/هیدروکسی آپاتیت (PCL-HA) اصلاح شده با فیبرین غنی از پلاکت (PRF) است.روش کار: داربست‌ها با استفاده از فناوری چاپ سه‌بعدی برای ایجاد محیطی مناسب جهت بازسازی استخوان ساخته شدند. میکروسکوپ الکترونی روبش (SEM)، تبدیل فوریه فروسر (FT-IR)، و تست‌های مکانیکی فشاری برای مشخص کردن مورفولوژی، ریزساختار و خواص مکانیکی داربست به کار گرفته شد. قابلیت چسبندگی سلولی، تکثیر، زیست سازگاری و تمایز نیز مورد بررسی قرار گرفت.نتایج: در نتیجه افزودن نانوذرات هیدروکسی آپاتیت (HA، داربست‌های PCL-HA چاپ سه‌بعدی با منافذ به هم پیوسته سطح ناهموار و خواص مکانیکی بهبود یافته داشتند. به دلیل آب دوستی و تخلخل بالاتر داربست PCL-HA/PRF در مقایسه با داربس PCL، رشد سلول‌های استخوانی در سطح داربست PCL-HA/PRF مشاهده شد. نتایج سنجش سمیت سلولی به طور قابل‌توجهی سازگاری سلولی داربست‌های PCL-HA/PRF را نسبت به داربست‌های PCL و PCL-HA نشان داد.نتیجه‌گیری نهایی: نتایج نشان می‌دهد که داربست‌های چاپ سه بعدی PCL-HA اصلاح شده با فیبرین غنی از پلاکت (PRF) می‌توانند در بازسازی بافت استخوانی مؤثر باشند.}, keywords_fa = {مهندسی بافت استخوان,داربست های چاپ سه بعدی,هیدروکسی آپاتیت,فیبرین غنی از پلاکت,تمایزسلول های استخوانی}, url = {https://ijvm.ut.ac.ir/article_86622.html}, eprint = {https://ijvm.ut.ac.ir/article_86622_154a9c8959720a33bfaf9116ecfa85d7.pdf} }